New features in the interactive bodies
Bodies 10, 50, 60, 70, 80
New adjustment options
|
If the aid point of the armhole curve is within a radius of 10 mm of the green point, a quarter arc appears with this point as the echo. This arc is formed with the perpendicular distance of the armhole low point to the aid line as the radius. The green radius point has a magnetic effect on the aid. The circular arc becomes visible again when the shape point of the armhole curve is activated at the bottom.
|
|
This is possible in the side seam drag area,.to interactively set the low point position of the armhole relative to the armhole width using a slider. To the left and right of the slider, the percentage values appear as an echo according to the X value setting. If these deviate from the measured percentage values at the bottom of the armhole width, they are shown in grey. It is now possible to change the position by shifting the armhole low point by millimetres. If both percentages at the top and bottom match again, the values at the top are displayed in green.
Bodice 10, 50, 60, 80
|
|
A dotted guide line appears for aligning the shoulder dart. It is aligned vertically or at the centre back, depending on the setting of the centre back option. This auxiliary line had a magnetic effect on the end point of the dart. It disappears as soon as its direction is the same as the direction of the dart centre.
|
|
To facilitate shoulder slope adjustment at the front and rear, mm values are now displayed on the rear armhole protrusion line. The rear measuring point (1) is formed as the intersection of the rear shoulder with the rear protrusion line and the front measuring point (2) as the intersection of the circular arc with radius from (4) to (5) with the front protrusion line. From this point, a perpendicular point (3) is shown on the rear protrusion line. The measured values are both displayed for the shoulder adjustment with measurements shoulder angle and length over shoulder.
This display is also visible for drag points in the bust dart and side seam drag areas, which change the armhole balance from front to back:
In the drag area bust dart, these are the drag points for setting the bust dart content in % and the armhole loosening in mm and in the drag area side seam, the drag points for pushing the side seam at the front or back.
Bodice 30
|
|
When selecting the first or second variant of the neckline grading option in the category neckline , up to four sliders appear in the drag area ease horizontal + vertical to additionally adjust the height and width of the neckline. There are also four new setting options in the drag area line relocation: for the adjustment of front length and for the relocation of the armhole, waist and hip lines. These new drag points allow an interactive change, even if the corresponding points have been linked with X, G or Z values.
Bodice 60
In the shoulder dart position option, the new variant position shoulder dart as bust dart appears in second place. The variant position as bust dart, alignment relative to back width shifts from the second to the third position. As in bodices 10, 50 and 80, three variants are also available for bodices 60.
|
|
In the drag area ease horizontal + vertical, four new sliders are available to additionally adjust the height and width of the neckline. In
the drag area line relocation, there are also new sliders for relocating the armhole and hip lines. These new drag points allow an interactive change, even if the corresponding points have been linked with X, G or Z values.
Bodice 70
-
Shoulder width with or without across back ease
When the first variant is activated, the shoulder and back width are set with the same allowance. The bust dart intake is reduced according to the addition. If required, this can be changed in the drag area bust dart. In the second variant, the ease for across back and shoulder are specified separately without influencing the bust dart intake.
|
As in bodices 10, 50, 60 and 80, there is now an additional option in bodice 70 to change the bust dart content in mm. When opening the dart with the slider (1), the armhole, shoulder and neck lines are moved upwards by the set amount and remain unchanged. The bust line can be moved using the slider (2). The upper side seam is always equalised so that it retains its original shape. This equalisation curve can be adjusted separately and is displayed on the back seam as a comparison curve.
Bodices 70 and 80
The option nape to waist over bust or neck to waist over bust is now also available in bodices 70 and 80 in the GRAFIS measurement system SIZES_1 in the category length.
-
Use nape to waist over bust or neck to waist over bust. Only in Sizes_1.
Bodice 80
The drag area shoulder dart has been added to bodice 80, resulting in new options in the category shoulder.
• Shoulder dart position
• Shoulder with lenght over shoulder or shoulder angle
• Shoulder with or without pinching the armhole
• Shoulder with or without rotation to the front ( only in GRASFIS measurement system SIZES_1
A slider is now available in bodice 80 to adjust the reduction of the gusset length.
|






